manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 79 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 79

Servicing the Air Filter

The air filter traps larger dust particles from entering the server. The air filter is located at

the air intake end of the server. See 

“Component Locations (Storage, Power, NVMe, and Fan

Modules)” on page 14

.

Description

Links

Replace the air filter.

“Remove the Filter” on page 79

“Install the Filter” on page 82

Remove the air filter as part of another

component's service operation.

“Remove the Filter” on page 79

Install the air filter as part of another

component's service operation.

“Install the Filter” on page 82

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Remove the Filter

Removing the air filter is a hot-swap operation. You do not need to power off the server before

you remove the air filter.

1.

Follow safety and ESD precautions.

See 

“Preparing for Service” on page 43

.

Servicing the Air Filter

79

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments