Oce Arizona 365 GT User Manual Download Page 82

Page: 82 / 234

Foot Pedal Switch Functions

Introduction

The foot pedal switches are used to control the forward and reverse movement of media shafts.

Summary of Dual Foot Pedal Switch Functions

The following table indicates the foot pedal functions for various RMO states.

Actions for foot pedals in various states

Media Reverse

Media Forward

RMO State

Left Hold

Left Tap

Right Hold

Right Tap

Load Media

Rewinds media
onto supply shaft

Unlocks media
supply shaft

Advance media
from supply shaft

Unlocks take-up
shaft

Initialized

Rewinds media

n/a

Advances media

n/a

Unload (before
media cut)

Important:

Don't touch the pedal switches

Media is positioned for cut when you click on the Unload icon

Cut the media, then proceed with unload

Unload (after me-
dia cut)

Unwinds media
from the take-up
roll

Rewinds media
and unlocks the
supply shaft

Winds media
back onto the
take-up shaft

Winds media and
unlocks the take-
up shaft

Foot Pedal Switch Functions

Chapter 6 - How to Operate the Roll Media Option

Summary of Contents for Arizona 365 GT











































































































































































































































Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands

Oce Arizona 365 GT, User Manual

Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands