Oce Arizona 365 GT User Manual Download Page 69

Page: 69 / 234

How to Lock Out the Power Switch

IMPORTANT

Some service procedures require locking out the On/Off switch to ensure operator safety. When

the switch is locked out, it is impossible to supply power to the printer.

Procedure

Refer to the Shutdown procedure "How to Power Off", at the beginning of this section.

Turn the AC power switch to the Off position.

Apply a lock and a tag-out label to the Lock-out area of the switch for the duration of any service
or maintenance procedures.

Perform service procedure (generally this is done by a service technician)

When maintenance or service is complete, remove the lock and tag-out label and turn the AC
power switch to the On position.

After you finish

How to Use the Disconnect Device

The AC power plug is the main disconnect device for the printer.

[36] AC Power Switch and Lockout

1. Follow the Lock-out procedure above.
2. For additional safety, also disconnect the AC power plug from the wall outlet.
3. When the printer is successfully moved or the repair work is complete, re-connect the power

plug and unlock the AC power switch.

How to Lock Out the Power Switch

Chapter 5 - How to Operate Your Océ Arizona Printer

Summary of Contents for Arizona 365 GT











































































































































































































































Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands

Oce Arizona 365 GT, User Manual

Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands