Home
/
Oce
/
Arizona 365 GT
/
User Manual

Oce Arizona 365 GT, User Manual

Share

Page: 138 / 234

background image

4.

Once that is done, replace path in the group above the image and clipping layers. Ensure that
Overprint is turned on.

[93] Replace path in Group

5.

Save the file.

NOTE

In testing, we have found the .eps file format to be the best. However, Postscript and
PDF files will work as well, but may require some additional setup. Make sure that
when you save the file, "Preserve Overprints" is enabled.

It is also possible and sometimes preferable, to print directly from Illustrator to Rip-Queue. For
instructions on how to do this, see the Onyx web site for a document called "Printing From a
Mac" (it also contains generic information on printing from Windows-based systems).

6.

Open the file in ProductionHouse.

How to Create a Spot Channel Path in Illustrator

138

Chapter 8 - How to Work With White Ink

«
...
136
137
138
139
140
...
»

Summary of Contents for Arizona 365 GT











































































































































































































































Reviews:

No comments

Related manuals for Arizona 365 GT

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

CJX-2000FW Series

Brand: Samsung Pages: 2

4116 - SCX B/W Laser

Brand: Samsung Pages: 205

3561ND - B/W Laser Printer

Brand: Samsung Pages: 252

3561ND - B/W Laser Printer

Brand: Samsung Pages: 127

Brand: Samsung Pages: 314

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands