NXP Semiconductors LPC84x Page 334 User Manual Download | Manualshive

Page: 334 / 515

background image

UM11029

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2017. All rights reserved.

User manual

Rev. 1.0 — 16 June 2017

334 of 515

NXP Semiconductors

UM11029

Chapter 19: LPC84x I2C0/1/2/3

19.3.2.2 Slave write to master

•

Set the SLVEN bit to 1 in the CFG register. See

•

Write the slave address x to the address 0 match register. See

Write data to the master:

1. Wait for the pending status to be set (SLVPENDING = 1) by polling the STAT register.
2. ACK the address by setting SLVCONTINUE = 1 in the slave control register. See

3. Wait for the pending status to be set (SLVPENDING = 1) by polling the STAT register.
4. Write 8 bits of data to SLVDAT register. See

5. Continue the transaction by setting SLVCONTINUE = 1 in the slave control register.

See

19.3.3 Configure the I2C for wake-up

In sleep mode, any activity on the I2C-bus that triggers an I2C interrupt can wake up the
part, provided that the interrupt is enabled in the INTENSET register and the NVIC. As
long as the I2C clock I2C_PCLK remains active in sleep mode, the I2C can wake up the
part independently of whether the I2C block is configured in master or slave mode.

In Deep-sleep or Power-down mode, the I2C clock is turned off as are all peripheral
clocks. However, if the I2C is configured in slave mode and an external master on the
I2C-bus provides the clock signal, the I2C block can create an interrupt asynchronously.
This interrupt, if enabled in the NVIC and in the I2C block’s INTENCLR register, can then
wake up the core.

19.3.3.1 Wake-up from Sleep mode

•

Enable the I2C interrupt in the NVIC.

•

Enable the I2C wake-up event in the I2C INTENSET register. Wake-up on any
enabled interrupts is supported (see the INTENSET register). Examples are the
following events:

–

Master pending

–

Change to idle state

–

Start/stop error

–

Slave pending

–

Address match (in slave mode)

–

Data available/ready

19.3.3.2 Wake-up from Deep-sleep and Power-down modes

•

Enable the I2C interrupt in the NVIC.

•

Enable the I2C interrupt in the STARTERP1 register in the SYSCON block to create
the interrupt signal asynchronously while the core and the peripheral are not clocked.
See

Table 169 “Start logic 1 interrupt wake-up enable register (STARTERP1, address

0x4004 8214) bit description”

.

«
...
332
333
334
335
336
...
»

Summary of Contents for LPC84x




































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC84x

Brand: OMA Pages: 53

Brand: M-system Pages: 7

Brand: Vestil Pages: 11

CPX-AP-I-8DI-M8-3P

Brand: Festo Pages: 18

Brand: Sandstrom Pages: 32

Brand: Zepro Pages: 64

Brand: FAAC Pages: 63

SPACOMMAND CP3800 Series

Brand: Pentair Pages: 36

Soul S5110/ART 7W

Brand: golmar Pages: 40

Brand: Guardian Audio Pages: 4

Brand: Presto Lifts Pages: 18

KPN235WEK-WELIK-DC

Brand: Ravaglioli Pages: 76

Brand: WaterGroup Pages: 24

3D TRASAR Series

Brand: Nalco Pages: 243

Brand: SRS Labs Pages: 7

Brand: Genie Pages: 44

Brand: Tyco Pages: 8

Brand: SMAR Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands