manualshive.com logo in svg

NXP Semiconductors LPC2880, User Manual

The NXP Semiconductors LPC2880, an advanced electronic component, comes with a comprehensive user manual. This valuable resource provides detailed instructions for optimum product utilization. Access the user manual for free download at manualshive.com, empowering you to explore all the features and functionalities of the LPC2880 effortlessly.

Share
Download
background image

UM10208_2

© NXP B.V. 2007. All rights reserved.

User manual

Rev. 02 — 1 June 2007 

138 of 362

NXP Semiconductors

UM10208

Chapter 12: LPC2800 Event router

4.

Register descriptions

The following table is arranged in the order than the various registers apply to the signal 
flow through the Event Router. That is, the outputs of the first register are applied to the 
input signals, and one of the last registers can be read to sense the state of the five 
outputs of the Event Router block.

 

Table 140. Event router register descriptions

Names

Description

Access Address = Reset value

EVAPR[0]
EVAPR[1]
EVAPR[2]
EVAPR[3]

Activation Polarity Registers.

 Each 0 in these 

registers indicates that the corresponding signal is 
low-active or falling-edge sensitive, each 1 indicates 
that the signal is high-active or rising-edge sensitive.

R/W

0x8000 0CC0 = 0xFFFF FFFD
0x8000 0CC4 = 0xFFFF FFFF
0x8000 0CC8 = 0xFF67 FFFF
0x8000 0CCC = 0x0000 003C

EVATR[0]
EVATR[1]
EVATR[2]
EVATR[3]

Activation Type Registers.

 Each 0 in these registers 

indicates that the corresponding signal is low- or 
high-active, each 1 indicates that the signal is edge 
sensitive.

R/W

0x8000 0CE0 = 0xFFFF FFFD 
0x8000 0CE4 = 0xFFFF FFFF
0x8000 0CE8 = 0xFF67 FFFF
0x8000 0CEC = 0x0000 003C

EVECLR[0]
EVECLR[1]
EVECLR[2]
EVECLR[3]

Edge Clear Registers.

 Writing a 1 to a bit in these 

registers that corresponds to an edge-sensitive 
signal, clears the edge-detection latch for that signal. 
0s written to these registers have no effect.

WO

0x8000 0C20
0x8000 0C24
0x8000 0C28
0x8000 0C2C

EVESET[0]
EVESET[1]
EVESET[2]
EVESET[3]

Edge Set Registers.

 Writing a 1 to a bit in these 

registers that corresponds to an edge-sensitive 
signal, sets the edge-detection latch for that signal. 0s 
written to these registers have no effect. These 
registers can be used to force an interrupt or wakeup.

WO

0x8000 0C40
0x8000 0C44
0x8000 0C48
0x8000 0C4C

EVRSR[0]
EVRSR[1]
EVRSR[2]
EVRSR[3]

Raw Status Registers.

 Each 1 in these read-only 

registers indicates that the corresponding signal is in 
its active state, or that an the edge selected by the 
corresponding bit in EVAPR has been detected.

R/W

0x8000 0D20 = 0x0003 FBFC
0x8000 0D24 = 0x0621 0000
0x8000 0D28 = 0x0080 0100
0x8000 0D2C = 0x0000 07C0

EVMASK[0]
EVMASK[1]
EVMASK[2]
EVMASK[3]

Global Mask Registers.

 Each 1 in these registers 

enables the corresponding signal to contribute to the 
five outputs of the Event Router block, as controlled 
by the subsequent Interrupt Output Mask Registers. 
These registers can be written during system 
initialization, but changing their values dynamically 
should be done using the Global Mask Set and Clear 
Registers.

R/W

0x8000 0C60 = 0xFFFF FFFF
0x8000 0C64 = 0xFFFF FFFF
0x8000 0C68 = 0xFFFF FFFF
0x8000 0C6C = 0x0000 07FF

EVMCLR[0:3]

Global Mask Clear Registers.

 Writing a 1 to a bit in 

these registers clears the Global Mask Register bit for 
that signal, thus disabling its ability to interrupt, 
activate a clock, or reset a module. 0s written to these 
registers have no effect.

WO

0x8000 0C80, 0x8000 0C84, 
0x8000 0C88, 0x8000 0C8C

EVMSET[0:3]

Global Mask Set Registers.

 Writing a 1 to a bit in 

these registers sets the Global Mask Register bit for 
that signal, thus enabling its ability to interrupt, 
activate a clock, or reset a module. 0s written to these 
registers have no effect.

WO

0x8000 0CA0, 0x8000 0CA4, 
0x8000 0CA8, 0x8000 0CAC

EVPEND[0:3]

Pending Registers.

 Each 1 in these read-only 

registers indicates that the corresponding signal is in 
its active state, or that an the edge selected by the 
corresponding bit in EVAPR has been detected, and 
that the signal is globally enabled.

RO

0x8000 0C00 = 0x0003 FBFC
0x8000 0C04 = 0x0621 0000
0x8000 0C08 = 0x0080 0100
0x8000 0C0C = 0x0000 07C0

Summary of Contents for LPC2880











































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC2880

Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Brand: Objective Imaging Pages: 11
YASKAWA Lift Inverter L1000V Technical Manual preview
Lift Inverter L1000V
Brand: YASKAWA Pages: 282
AMX NetLinx Integrated Controller NI-3100 Installation Manual preview
NetLinx Integrated Controller NI-3100
Brand: AMX Pages: 2
NI RMC-8355 User Manual preview
RMC-8355
Brand: NI Pages: 135
Danfoss OBC 80 Series Manual preview
OBC 80 Series
Brand: Danfoss Pages: 16
Ibiza LC192DMX-MINI User Manual preview
LC192DMX-MINI
Brand: Ibiza Pages: 37
Bardac PLX Product Manual preview
PLX
Brand: Bardac Pages: 235
Instruments of Things IO-Lights User Manual preview
IO-Lights
Brand: Instruments of Things Pages: 12
Halma Alicat Scientific IVCD Operating Manual preview
Alicat Scientific IVCD
Brand: Halma Pages: 28
gefran 1200-RD00-00-0 Series Quick Start Manual preview
1200-RD00-00-0 Series
Brand: gefran Pages: 6
Magnetek IMPULSE G Plus Series 4 Installation Manual preview
IMPULSE G Plus Series 4
Brand: Magnetek Pages: 60
ST VL53L4CD User Manual preview
VL53L4CD
Brand: ST Pages: 22
Alpha C016-1540-10 Technical Manual preview
C016-1540-10
Brand: Alpha Pages: 16
Salus PC11W Manual preview
PC11W
Brand: Salus Pages: 2
CTR Electronics CANdle User Manual preview
CANdle
Brand: CTR Electronics Pages: 22
Samson TROVIS 5433 Quick Manual preview
TROVIS 5433
Brand: Samson Pages: 2
Leviton 73A00-3ZB Installation Instructions And User Manual preview
73A00-3ZB
Brand: Leviton Pages: 2
XCI SmartZone SPC Instructions preview
SmartZone SPC
Brand: XCI Pages: 2

Brands by name

Popular brands

Load more brands