NXP Semiconductors LPC2880 User Manual Download Page 160

Page: 160 / 362

UM10208_2

User manual

Rev. 02 — 1 June 2007

160 of 362

NXP Semiconductors

UM10208

Chapter 14: LPC2800 UART

3.8 Line Control Register (LCR - 0x8010 100C)

The LCR controls the format of the data characters that are to be transmitted or received.

Table 175. Line Control Register (LCR - 0x8010 100C)

Bit

Name

Value Description

Reset
value

1:0

Word Length
Select

5 bit characters

6 bit characters

7 bit characters

8 bit characters

Stop Bit Select

Send 1 stop bit.

Send 2 stop bits (1.5 if LCR[1:0]=00).

Parity Enable

Disable parity generation and checking.

Enable parity generation and checking.

5:4

Parity Select

Odd parity. The number of 1s in each transmitted character
and the attached parity bit will be odd.

Even Parity. The number of 1s in each transmitted
character and the attached parity bit will be even.

Send "1" in parity bits.

Send "0" in parity bits.

Break Control

Disable break transmission.

Enable break transmission. Output pin TXD is forced low
when LCR[6] is 1.

Divisor Latch
Access Bit
(DLAB)

Disable access to Divisor Latches.

Enable access to Divisor Latches.

31:8 -

Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.

Summary of Contents for LPC2880










































































































































































































































































































































































Search results

Summary of Contents for LPC2880

Reviews:

Related manuals for LPC2880

Brands by name

Popular brands

NXP Semiconductors LPC2880, User Manual

Search results

Summary of Contents for LPC2880

Reviews:

Related manuals for LPC2880

Brands by name

Popular brands