manualshive.com logo in svg

NXP Semiconductors LPC2880, User Manual

The NXP Semiconductors LPC2880, an advanced electronic component, comes with a comprehensive user manual. This valuable resource provides detailed instructions for optimum product utilization. Access the user manual for free download at manualshive.com, empowering you to explore all the features and functionalities of the LPC2880 effortlessly.

Share
Download
background image

UM10208_2

© NXP B.V. 2007. All rights reserved.

User manual

Rev. 02 — 1 June 2007 

37 of 362

NXP Semiconductors

UM10208

Chapter 5: LPC2800 Flash

5.3 Flash Program Time register (F_PROG_TIME - 0x8010 2008)

The Flash Program Time register controls the timer for all Flash programming tasks. It 
also allows to read the remaining program or erase time. The fields in the F_PROG_TIME 
register are shown in 

Table 5–15

.

 

5.4 Flash Wait States register (F_WAIT - 0x8010 2010)

The Flash Wait State register controls the number of wait states that are used for flash 
reads. The fields in the F_WAIT register are shown in 

Table 5–16

.

 

5.5 Flash Clock Divider register (F_CLK_TIME - 0x8010 201C)

The Flash Clock Divider register controls the divider for the clock that is used by Flash 
programming and erase operations. This clock must be set up to provide 66 kHz prior to 
beginning programming or erase operations. The fields in the F_CLK_TIME register are 
shown in 

Table 5–17

.

Table 15.

Flash Program Time register (F_PROG_TIME - 0x8010 2008)

Bits

Name

Description

Access Reset

value

14:0

FPT_TIME

Programming timer. Remaining program/erase time is 
512

×

FPT_TIME clock cycles.

R/W

0

15

FPT_ENABLE Program timer Enable.

0 : timer disabled.

1 : timer enabled.

R/W

0

31:16 -

Reserved, user software should not write ones to 
reserved bits. The value read from a reserved bit is not 
defined.

-

-

Table 16.

Flash Wait States register (F_WAIT - 0x8010 2010)

Bits

Name

Description

Access Reset

value

7:0

WAIT_STATES Defines the number of wait states used for flash read 

operations.

R/W

0x04

13:8

-

Reserved, user software should not write ones to 
reserved bits. The value read from a reserved bit is not 
defined.

-

-

15:14 -

Reserved, these bits must be left at the reset state (both 
bits = 1)

R/W

0x03

31:16 -

Reserved, user software should not write ones to 
reserved bits. The value read from a reserved bit is not 
defined.

-

-

Summary of Contents for LPC2880











































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC2880

D-Link DSN-640 Quick Installation Manual preview
DSN-640
Brand: D-Link Pages: 40
Vageo DT-1 Plus Manual preview
DT-1 Plus
Brand: Vageo Pages: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Brand: Vacon Pages: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Brand: Vacon Pages: 24
Vacon 100X series Marine Installation Manual preview
100X series
Brand: Vacon Pages: 30
Vacon 100 flow User Manual preview
100 flow
Brand: Vacon Pages: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Brand: Vacon Pages: 100
Riello 20120499 Manual preview
20120499
Brand: Riello Pages: 72
McIntosh MHT200 Owner'S Manual preview
MHT200
Brand: McIntosh Pages: 68
Harmonic Drive RSF-B mini Series Manual preview
RSF-B mini Series
Brand: Harmonic Drive Pages: 32
iDTRONIC BLEUBOX R-IN-UHF-5239U Manual preview
BLEUBOX R-IN-UHF-5239U
Brand: iDTRONIC Pages: 13
D+H VCD 203 Manual preview
VCD 203
Brand: D+H Pages: 16
CompuPro DISK 3 Technical Manual preview
DISK 3
Brand: CompuPro Pages: 33
Nibe Uplink Installer Manual preview
Uplink
Brand: Nibe Pages: 20
Curtis PMC 1204 Series Manual preview
PMC 1204 Series
Brand: Curtis Pages: 56
OK-I PTZ-KB050 Operational Manual preview
PTZ-KB050
Brand: OK-I Pages: 10
AUMA PROFOX PF-M100X Manual preview
PROFOX PF-M100X
Brand: AUMA Pages: 56
SUNWIND DR2210N -DDB User Manual preview
DR2210N -DDB
Brand: SUNWIND Pages: 53

Brands by name

Popular brands

Load more brands