manualshive.com logo in svg

NXP Semiconductors LPC2880, User Manual

The NXP Semiconductors LPC2880, an advanced electronic component, comes with a comprehensive user manual. This valuable resource provides detailed instructions for optimum product utilization. Access the user manual for free download at manualshive.com, empowering you to explore all the features and functionalities of the LPC2880 effortlessly.

Share
Download
background image

UM10208_2

© NXP B.V. 2007. All rights reserved.

User manual

Rev. 02 — 1 June 2007 

39 of 362

NXP Semiconductors

UM10208

Chapter 5: LPC2800 Flash

 

5.6.3 Flash Interrupt Clear register (F_INT_CLR - 0x8010 2FE8)

The Flash Interrupt Clear register allows clearing of individual interrupt flags for the flash 
memory. These flags may be read in the F_INT_STAT register. The fields in the 
F_INT_CLR register are shown in 

Table 5–20

.

 

5.6.4 Flash Interrupt Enable register (F_INTEN - 0x8010 2FE4)

The Flash Interrupt Enable register indicates which of the interrupt flags that are 
associated with programming and erase functions are enabled to send interrupt requests 
to the interrupt controller. Additional control of interrupts is provided by the interrupt 
controller itself. The fields in the F_INTEN register are shown in 

Table 5–21

.

 

5.6.5 Flash Interrupt Enable Set register (F_INTEN_SET - 0x8010 2FDC)

The Flash Interrupt Enable Set register allows setting of individual interrupt enable bits for 
the interrupt flags that are associated with programming and erase functions. The fields in 
the F_INTEN_SET register are shown in 

Table 5–22

.

Table 19.

Flash Interrupt Set register (F_INT_SET - 0x8010 2FEC)

Bits Name

Description

Access Reset

value

1:0

SET_INT These bits allow software setting of interrupt flag bits in the 

F_INT_STAT register.

0 : leave the corresponding bit unchanged.

1: set the corresponding bit.

WO

-

31:2 -

Reserved, user software should not write ones to reserved bits.  -

-

Table 20.

Flash Interrupt Clear register (F_INT_CLR - 0x8010 2FE8)

Bits Name 

Description

Access Reset

value

1:0

CLR_INT These bits allow software clearing of interrupt flag bits in the 

F_INT_STAT register.

0 : leave the corresponding bit unchanged.

1: clear the corresponding bit.

WO

-

31:2

Reserved, user software should not write ones to reserved bits.  -

-

Table 21.

Flash Interrupt Enable register (F_INTEN - 0x8010 2FE4)

Bits Name

Description

Access Reset

Value

0

EOE_ENABLE End-of-erase interrupt enable bit.

This bit is set when a 1 is written to F_INTEN_SET[0].

This bit is cleared when a 1 is written to F_INTEN_CLR[0].

RO

0

1

EOP_ENABLE End-of-Program interrupt enable bit.

This bit is set when a 1 is written to F_INTEN_SET[1].

This bit is cleared when a 1 is written to F_INTEN_CLR[1].

RO

0

31:2 -

Reserved. The value read from a reserved bit is not 
defined.

-

-

Summary of Contents for LPC2880











































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC2880

Hanbay RC Series Manual preview
RC Series
Brand: Hanbay Pages: 18
DayTronic 3700 Series Instruction Manual preview
3700 Series
Brand: DayTronic Pages: 22
eclisse E-MOTION Installation, Operation And Maintenance Manual preview
E-MOTION
Brand: eclisse Pages: 40
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Brand: Harpo Pages: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Brand: Hardi Pages: 2
OES ISC-9000 Operational Instructions preview
ISC-9000
Brand: OES Pages: 3
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 112
Samson 46-7 Mounting And Operating Instructions preview
46-7
Brand: Samson Pages: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Brand: Hansen Pages: 12
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Brand: mikroElektronika Pages: 35
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Brand: Davey Pages: 8
SMC Networks ITV 0 Series Instruction Manual preview
ITV 0 Series
Brand: SMC Networks Pages: 2
Rain Evo 1 Instructions Manual preview
Evo 1
Brand: Rain Pages: 8
Autopilot ECLIPSE F90 User Manual preview
ECLIPSE F90
Brand: Autopilot Pages: 12
Embedded Systems LogicMachine Reactor Lite Quick Start Manual preview
LogicMachine Reactor Lite
Brand: Embedded Systems Pages: 7
second sound ACO160 Quick Start Manual preview
ACO160
Brand: second sound Pages: 4
Texmate Tiger 320 DI-503E Manual preview
Tiger 320 DI-503E
Brand: Texmate Pages: 44
Plettenberg MST60-80 Operational Manual preview
MST60-80
Brand: Plettenberg Pages: 17

Brands by name

Popular brands

Load more brands