manualshive.com logo in svg

NXP Semiconductors LPC2880, User Manual

The NXP Semiconductors LPC2880, an advanced electronic component, comes with a comprehensive user manual. This valuable resource provides detailed instructions for optimum product utilization. Access the user manual for free download at manualshive.com, empowering you to explore all the features and functionalities of the LPC2880 effortlessly.

Share
Download
background image

UM10208_2

© NXP B.V. 2007. All rights reserved.

User manual

Rev. 02 — 1 June 2007 

174 of 362

NXP Semiconductors

UM10208

Chapter 14: LPC2800 UART

3.25 Interrupt Clear Enable Register (INTCE - 0x8010 1FD8)

Writing a 1 to certain bits in this write-only register clears the corresponding bit in INTE, 
thus disabling the corresponding bit in the INTS register from causing a UART interrupt 
request. Zero bits written to this register have no effect.

 

3.26 Interrupt Enable Register     (INTE  -  0x8010 1FE4)

Bits 15:12, 9:4, and 0 in this read-only register are 1 if the corresponding bit in INTS is 
enabled to cause a UART interrupt, and 0 if not.

 

Table 192. Interrupt Clear Enable Register     (INTCE  -  0x8010 1FD8)

Bit

Name

Description

Reset
value

0

DCTSIEClr

Writing a 1 to this bit clears the DCTSIE bit in the INTE register.

-

3:1

Reserved. Software should not write ones to reserved bits. 

-

4

THREIEClr

Writing a 1 to this bit clears The THREIE bit in the INTE register.

-

5

RxTOIEClr

Writing a 1 to this bit clears the RTXOIE bit in the INTE register.

-

6

RxDAIEClr

Writing a 1 to this bit clears the RxDAIE bit in the INTE register.

-

7

WakeUpIEClr

Writing a 1 to this bit clears the WakeUpIE bit in the INTE register.

-

8

ABEOIEClr

Writing a 1 to this bit clears the ABEOIE bit in the INTE register.

-

9

ABTOIEClr

Writing a 1 to this bit clears the ABTOIE bit in the INTE register.

-

11:10

Reserved. Software should not write ones to reserved bits.

-

12

BreakIEClr

Writing a 1 to this clears the BreakIE bit in the INTE register.

-

13

FEIEClr

Writing a 1 to this clears the FEIE bit in the INTE register.

-

14

PEIEClr

Writing a 1 to this clears the PEIE bit in the INTE register.

-

15

OEIEClr

Writing a 1 to this bit clears the OEIE bit in the INTE register.

-

31:16

Reserved. Software should not write ones to reserved bits.

-

Table 193. Interrupt Enable Register     (INTE  -  0x8010 1FE4)

Bit

Name

Description

Reset
value

0

DCTSIE

This bit is 1 if the DCTSInt bit in INTE is interrupt-enabled.

0

3:1

Reserved. The value read from a reserved bit is not defined. 

-

4

THREIE

This bit is 1 if The THREInt bit in INTE is interrupt-enabled.

0

5

RxTOIE

This bit is 1 if the RTXOInt bit in INTE is interrupt-enabled.

0

6

RxDAIE

This bit is 1 if the RxDAInt bit in INTE is interrupt-enabled.

0

7

WakeUpIE

This is 1 if the WakeUpInt bit in INTE is interrupt-enabled.

0

8

ABEOIE

This bit is 1 if the ABEOInt bit in INTE is interrupt-enabled.

0

9

ABTOIE

This bit is 1 if the ABTOInt bit in INTE is interrupt-enabled.

0

11:10

Reserved. The value read from a reserved bit is not defined.

-

12

BreakIE

This is 1 if the BreakInt bit in INTE is interrupt-enabled.

0

13

FEIE

This is 1 if the FEInt bit in INTE is interrupt-enabled.

0

14

PEIE

This is 1 if the PEInt bit in INTE is interrupt-enabled.

0

15

OEIE

This bit is 1 if the OEInt bit in INTE is interrupt-enabled.

0

31:16

Reserved. The value read from a reserved bit is not defined.

-

Summary of Contents for LPC2880











































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC2880

Data Aire dap4 touch Protocol Manual preview
dap4 touch
Brand: Data Aire Pages: 13
Harmonic Drive CHA Engineering Data preview
CHA
Brand: Harmonic Drive Pages: 85
Watts 009 Series Instruction, Installation, Maintenance And Repair Manual preview
009 Series
Brand: Watts Pages: 24
tbs electronics Omnicharge Solar OCS 100-20 Installation Manual preview
Omnicharge Solar OCS 100-20
Brand: tbs electronics Pages: 64
AUMA GSTI 25.1 Operating Instructions Manual preview
GSTI 25.1
Brand: AUMA Pages: 24
McIntosh MHT200 Service Manual preview
MHT200
Brand: McIntosh Pages: 60
Ruida Technology RDLC320 User Manual preview
RDLC320
Brand: Ruida Technology Pages: 45
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Brand: H.E. Anderson Pages: 11
Freescale Semiconductor RS08 Designer Reference Manual preview
RS08
Brand: Freescale Semiconductor Pages: 34
Matelec FPC-12720 Quick Start Manual preview
FPC-12720
Brand: Matelec Pages: 2
Progeny Crystal.PoE V4 Manual preview
Crystal.PoE V4
Brand: Progeny Pages: 4
Evco EVCLC229N9E Manual preview
EVCLC229N9E
Brand: Evco Pages: 78
Melexis DVK90121 User Manual preview
DVK90121
Brand: Melexis Pages: 13
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Brand: Galcon Pages: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Brand: NXP Semiconductors Pages: 5
Inner Range CONCEPT IQ User Manual preview
CONCEPT IQ
Brand: Inner Range Pages: 28
Danfoss EKC 331T Instructions Manual preview
EKC 331T
Brand: Danfoss Pages: 12
Icom IC-FC5000E Service Manual preview
IC-FC5000E
Brand: Icom Pages: 23

Brands by name

Popular brands

Load more brands