NEC V850/SA1 mPD703015 Preliminary User'S Manual Download Page 317

Page: 317 / 387

317

CHAPTER 12 DMA FUNCTIONS

12.1 Functions

The DMA (Direct Memory Access) controller transfers data between memory and peripheral I/Os based on DMA

requests sent from on-chip peripheral hardware (such as the serial interface, timer, or A/D converter).

This product includes three independent DMA channels that can transfer data in 8-bit and 16-bit units. The

maximum number of transfers is 256 and transfers are enabled only in single transfer mode.

After a DMA transfer is completed, DMA transfer completion interrupt (INTDMA0 to INTDMA2) requests are output

independently from the various channels.

The priority levels of the DMA channels are fixed as follows.

DMA0 > DMA1 > DMA2

12.2 Transfer Completion Interrupt Request

When a DMA transfer is completed and the TCn bit in the corresponding DMA channel control register (DCHCn) has

been set (to “1”), a DMA transfer completion interrupt request (INTDMA0 to INTDMA2) occurs on each channel in

relation to the interrupt controller.

12.3 Control Registers

(1) DMA peripheral I/O address registers 0 to 2 (DIOA0 to DIOA2)

These registers are used to set the peripheral I/O register’s address for DMA channel n. There is no

incrementation function.

Read and write in 16-bit units are enabled.

Figure 12-1. Format of DMA Peripheral I/O Address Registers 0 to 2 (DIOA0 to DIOA2)

After reset:

undefined

R/W

Address : DIOA0

FFFFF180H

DIOA1

FFFFF190H

DIOA2

FFFFF1A0H

DIOAn

IOAn9-IOAn1

(n = 0-2)

Caution

The following peripheral I/O registers cannot be set.

P4, P5, P6, P9, P11, P12, PM4, PM5, PM6, PM9, PM11, PM12, PMC12, MM, DWC, BCC, SYC,

PSC, PCC, SYS, PRCMD, DIOAn, DRAn, DBCn, DCHCn

Summary of Contents for V850/SA1 mPD703015




































































































































































































































































































































































































Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands

NEC V850/SA1 mPD703015, Preliminary User'S Manual

Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands