NEC V850/SA1 mPD703015 Preliminary User'S Manual Download Page 158

Page: 158 / 387

CHAPTER 7 TIMER/COUNTER FUNCTION

158

7.2

Operation

7.2.1 Operation as interval timer (16 bits)

Timer 0 operates as an interval timer when the 16-bit timer mode control register n (TMCn) and capture/compare

control register n (CRCn) are set as shown in Figure 7-7.

In this case, timer 0 repeatedly generates an interrupt at the time interval specified by the count value set in

advance to the 16-bit capture/compare register n (CRn0, CRn1).

When the count value of the 16-bit timer register n (TMn) coincides with the set value of CRn0, the value of TMn is

cleared to 0, and the timer continues counting. At the same time, an interrupt request signal (INTTMn0) is generated.

The count clock of the 16-bit timer/event counter can be selected by bits 0 and 1 (PRMn0 and PRMn1) of the

prescaler mode register n (PRMn).

Figure 7-7. Control Register Settings When Timer 0 Operates as Interval Timer

(a) 16-bit timer mode control register 0, 1 (TMC0, TMC1)

TMCn3

TMCn2

TMCn1

OVFn

TMCn

0/1

Clears and starts on

coincidence between

TMn and CRn0.

(b) Capture/compare control register 0, 1 (CRC0, CRC1)

CRCn2

CRCn1

CRCn0

CRCn

0/1

CRn0 as compare

Remark

0/1: When these bits are reset to 0 or set to 1, the other functions can be used along with the interval

timer function. For details, refer to Figures 7-2 and 7-3.

Summary of Contents for V850/SA1 mPD703015




































































































































































































































































































































































































Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands

NEC V850/SA1 mPD703015, Preliminary User'S Manual

Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands