NEC V850/SA1 mPD703015 Preliminary User'S Manual Download Page 260

Page: 260 / 387

CHAPTER 10 SERIAL INTERFACE FUNCTION

260

10.3.6 Interrupt request (INTIIC0) generation timing and wait control

The setting of bit 3 (WTIM) in the IIC control register (IICC0) determines the timing by which INTIIC0 is generated

and the corresponding wait control, as shown in Table 10-3.

Table 10-3. INTIIC0 Timing and Wait Control

During slave device operation

During master device operation

Address

Data reception

Data transmission

Address

Data reception

Data transmission

Notes 1, 2

Note 2

Notes 1, 2

Note 2

Notes 1.

The slave device’s INTIIC0 signal and wait period occurs at the falling edge of the ninth clock only when

there is a match with the address set to the slave address register (SVA0).

At this point, ACK is output regardless of the value set to IICC0’s bit 2 (ACKE). For a slave device that

has received an extension code, INTIIC0 occurs at the falling edge of the eighth clock.

If the received address does not match the contents of the slave address register (SVA0), neither INTIIC0

nor a wait occurs.

Remark

The numbers in the table indicate the number of the serial clock’s clock signals. Interrupt requests and

wait control are both synchronized with the falling edge of these clock signals.

WTIM

Summary of Contents for V850/SA1 mPD703015




































































































































































































































































































































































































Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands

NEC V850/SA1 mPD703015, Preliminary User'S Manual

Search results

Summary of Contents for V850/SA1 mPD703015

Reviews:

Related manuals for V850/SA1 mPD703015

Brands by name

Popular brands