manualshive.com logo in svg

NEC V850/SA1 mPD703015, Preliminary User'S Manual

Share
Download
NEC V850/SA1 mPD703015 Preliminary User'S Manual Download Page 89

 CHAPTER  4   BUS  CONTROL  FUNCTION

89

4.6  Idle State Insertion Function

To facilitate interfacing with low-speed memory devices and meeting the data output float delay time on memory

read accesses, one idle state (TI) can be inserted into the current bus cycle after the T3 state.  The bus cycle follow-

ing continuous bus cycles starts after one idle state.

Specifying insertion of the idle state is programmable by using the bus cycle control register (BCC).

Immediately after the system has been reset, idle state insertion is automatically programmed for all memory

blocks.

(1)  Bus cycle control register (BCC)

This register can be read/written in 16-bit units.

After reset: AAAAH

R/W

Address:  FFFFF062H

Symbol

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

BCC

Idle State Insert Specification

0

Not inserted

1

Inserted

n

Blocks into Which Idle State Is Inserted

0

Blocks 0/1

1

Blocks 2/3

2

Blocks 4/5

3

Blocks 6/7

4

Blocks 8/9

5

Blocks 10/11

6

Blocks 12/13

7

Blocks 14/15

Block 0 is reserved for the internal ROM area; therefore, no idle state is specified regardless of the BCC setting.

The internal RAM area and on-chip peripheral I/O area of block 15 are not subject to insertion of the idle state.

Be sure to set bits 0, 2, 4, 6, 8, 10, 12, and 14 to 0.  If these bits are set to 1, the operation is not guaranteed.

0

BC01

0

BC11

0

BC21

0

BC31

0

BC41

0

BC51

0

BC61

0

BC71

BCn1

1

Summary of Contents for V850/SA1 mPD703015




































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands