NEC N8400-086F User Manual Download

Page: 208 / 294

9-16 Upgrading Your Server

Installation

Install the DIMM on the CPU blade depending on the following procedure:

After the shutdown processing for the CPU blade to be removed, turn off the power of the
CPU blade.

Pull out the CPU blade from the Blade Enclosure.

Refer to the User's Guide of the Blade Enclosure.

Place the CPU blade on anti-static sheet with little dust.

Remove the two screws fixing the top cover.

Firmly hold the cover, move it slightly toward the rear of the blade, then lift the cover to
remove it from the CPU blade.

IMPORTANT:

Handle the cover carefully so as not to make it contact

with any electronic devices on the CPU blade.

Summary of Contents for N8400-086F







































































































































































































































































































Search results

Summary of Contents for N8400-086F

Reviews:

Related manuals for N8400-086F

Brands by name

Popular brands

NEC N8400-086F, User Manual

Search results

Summary of Contents for N8400-086F

Reviews:

Related manuals for N8400-086F

Brands by name

Popular brands