Home
/
NEC
/
ELECTRA ELITE IPK II
/
Programming Manual

NEC ELECTRA ELITE IPK II, Programming Manual, Page: 350 / 617

Share

Page: 350 / 617

NEC ELECTRA ELITE IPK II Programming Manual Download Page 350

Electra Elite IPK II

Document Revision 1

Electra Elite IPK II Programming Manual

2 - 315

Description

Use Program 31-06 : External Speaker Control to define the settings for the
external speaker using an amplifier.

Program 31 : Paging Setup

31-06 : External Speaker Control

Level:

IN

Input Data

External Speaker Number

1~9

Item

No.

Item

Input Data

Default

01

Broadcast Splash Tone Before
Paging (Paging Start Tone)

Use this option to enabled or
disable splash tone before Paging
over an external zone. If enabled,
the system broadcasts a splash
tone before the External Paging
announcement.

0

= No Tone (None)

1

= Splash Tone

2

= Chime Tone

2

02

Broadcast Splash Tone After
Paging (Paging End Time)

Use this option to enabled or
disable splash tone after Paging
over an external zone. If enabled,
the system broadcasts a splash
tone at the end of an External
Paging announcement.

0

= No Tone (None)

1

= Splash Tone

2

= Chime Tone

2

03

Speech Path

Determine if the external speaker
will be used for talkback (As this
option is not available with the
CPUII external page zone,
speaker 9 should be left at “1”.

0

= Both Way (Duplex)

1

= One Way (PGD -> SPK)

(Simplex)

1

04

CODEC Transmit Gain Setup

1~63 (-15.5 ~ +15.5dB)

32

05

CODEC Receive Gain Setup

1~63 (-15.5 ~ +15.5dB)

32

«
...
348
349
350
351
352
...
»

Summary of Contents for ELECTRA ELITE IPK II










































































































































































































































































































































































































































































































































































































































Reviews:

No comments