manualshive.com logo in svg

NEC ELECTRA ELITE IPK II, Programming Manual, Page: 228 / 617

Share
Download
NEC ELECTRA ELITE IPK II Programming Manual Download Page 228

Electra Elite IPK II

Document Revision 1

Electra Elite IPK II Programming Manual

2 - 193

Conditions

None

Feature Cross Reference

J

ISDN Compatibility

12

Call Forward Options (Auto Connect Send)

Incoming Calls Forwarded Out Automatically Return 
Connect Message When Outgoing  Call Receives 
Alerting Message.

0 = Normal - No 

Message (Off)

1 = Normal - No 

Message (On)

0

13

Local Busy Tone (Release)

Busy tone send when T-point receiving a RELEASE 
message from Network.

0 = Off
1 = On

0

14

No Response Release Send

Operation mode setting for when second T303 timer is 
expired.

0 = Off
1 = On

0

Input Data

Item 

No.

Item

Input Data

Default

Summary of Contents for ELECTRA ELITE IPK II










































































































































































































































































































































































































































































































































































































































Reviews:

No comments