MR VACUTAP VR Installation And Commissioning Instructions Download Page 90 | Manualshive

Page: 90 / 268

background image

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

90

4349315/00 EN

VACUTAP® VR®

Assembly: Bell-type tank design

WARNING

Risk of crushing from moving parts!

When the on-load tap-changer undertakes a tap-change operation, compo-
nents move on the selector and change-over selector, some of which are
freely accessible. Reaching into the selector or change-over selector during
a tap-change operation may result in serious injuries.
► Keep at a safe distance of at least 1 m during tap-change operations.
► Do not reach into the selector or change-over selector during tap-

change operations.

► Do not switch the on-load tap-changer when working on the selector

and change-over selector.

This chapter describes how to install the on-load tap-changer in a transform-
er in the bell-type tank design and how to dry it.

Preparatory work

Perform the work stated below before installing the on-load tap-changer in
the transformer.

Fitting mounting flange on transformer cover

A mounting flange is required for fitting the on-load tap-changer head on the
transformer cover. This can be supplied as an option or can be produced by
the customer. Mounting flanges made by the customer must comply with the
installation drawings in the appendix.
►

NOTICE!

Fit mounting flange on transformer cover (pressure tight).En-

sure that the sealing face makes complete contact and is not damaged.

Figure 94: Mounting flange

6

6.1

6.1.1

«
...
88
89
90
91
92
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: B. Braun Pages: 2

Aesculap Neurosurgery

Brand: B. Braun Pages: 13

Aesculap AdTec mini

Brand: B. Braun Pages: 2

Brand: B.Well Pages: 2

Brand: B. Braun Pages: 55

BA Ultimate LED

Brand: B.A. International Pages: 234

Brand: TDR Pages: 8

Brand: Olympus Pages: 130

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands