MR VACUTAP VR Installation And Commissioning Instructions Download Page 98

Page: 98 / 268

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

4349315/00 EN

VACUTAP® VR®

Remove the blocking strip from the tap selector coupling. Once the
blocking strip is removed, the tap selector coupling must no longer be
turned.

Figure 107: Blocking strip

CAUTION!

Place the oil compartment on a level surface and secure

it against tipping. An unstably positioned oil compartment may tip over,
resulting in serious injuries and damage.

Lift the oil compartment by hooking up the on-load tap-changer head
and remove the blocking device on the coupling of the oil compartment
base.

Figure 108: Blocking plate and shackle

Summary of Contents for VACUTAP VR













































































































































































































































































Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands

MR VACUTAP VR, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands