MR VACUTAP VR Installation And Commissioning Instructions Download Page 115 | Manualshive

Page: 115 / 268

background image

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

115

4349315/00 EN

VACUTAP® VR®

Removing on-load tap-changer head

Removing on-load tap-changer head cover

WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory

control, pressure relief device, pressure-operated relays) before remov-
ing the on-load tap-changer head cover.

► Do not operate any electric devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes and pump equipment

that are approved for flammable liquids.

NOTICE

Damage to the on-load tap-changer and transformer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer and transformer!
► Take care to avoid parts falling into the oil compartment.
► Check that you have the same number of small parts when disassem-

bling and reassembling.

1.

Remove temporary fastening and spacers and slowly lower on-load tap-
changer.

Figure 129: Removing fastening

6.7

6.7.1

«
...
113
114
115
116
117
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: UnionSpecial Pages: 56

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: ACDC Pages: 4

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands