MR VACUTAP VR Installation And Commissioning Instructions Download Page 224 | Manualshive

Page: 224 / 268

background image

12 Fault elimination

Maschinenfabrik Reinhausen GmbH 2015

224

4349315/00 EN

VACUTAP® VR®

Error pattern

Action

Tripping of pressure relief device (for example
MPreC®)

Remove diverter switch insert following maintenance
manual for the relevant on-load tap-changer. De-
pending on the cause of tripping, take measure-
ments/carry out checks on the transformer.

Tripping of pressure-operated relay (for example DW
2000)

Remove diverter switch insert following maintenance
manual for the relevant on-load tap-changer. De-
pending on the cause of tripping, take measure-
ments/carry out checks on the transformer.

Activation of tap-change supervisory control

Remove diverter switch insert following maintenance
manual for the relevant on-load tap-changer. De-
pending on the cause of tripping, take measure-
ments/carry out checks on the transformer.

Activation of rupture disk in on-load tap-changer
head cover

Remove diverter switch insert following maintenance
manual for the relevant on-load tap-changer. De-
pending on the cause of tripping, take measure-
ments/carry out checks on the transformer.

Tripping of motor protective switch in motor-drive
unit

Request "Information sheet on motor protective
switch tripping" from MR, complete and return to
MR.

Tripping of signaling contact that indicates that the
oil has fallen below the minimum oil level in the on-
load tap-changer oil conservator

Check pipework system (pipes etc.) and on-load tap-
changer head for leaks. Check oil level and oil quali-
ty of diverter switch oil in accordance with operating
instructions for on-load tap-changer. If the oil falls
below the limit values, also contact MR.

On-load tap-changer not changing tap position (slug-
gishness, Raise keys/Lower keys not working, divert-
er switch action not audible)

Contact MR.

No change in voltage on transformer despite change
in position on motor-drive unit

Contact MR.

Tap position indicator on motor-drive unit and on-
load tap-changer different

Contact MR.

Noises on drive shaft or motor-drive unit when
changing tap position

Ensure proper mounting of the drive shaft in accord-
ance with its operating instructions. Check that hose
clips and protective covers are seated correctly.
Contact MR in the event of noise from the motor-
drive unit.

Red message on monitoring unit

If possible read out database and send to MR along
with error code.

Warning or tripping of Buchholz relay on transformer Notify manufacturer of transformer.

Deviation from desired value when measuring wind-
ing resistance of transformer

Contact manufacturer of transformer and, if necessa-
ry, MR and provide measured values.

Deviation from desired value during dissolved gas
analysis (transformer oil)

Contact manufacturer of transformer and, if necessa-
ry, MR and provide measured values.

«
...
222
223
224
225
226
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

ACS880-01 Series

Brand: ABB Pages: 238

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Sonopuls HD 4050

Brand: BANDELIN Pages: 48

Brand: Tascam Pages: 8

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Monolith NT.115

Brand: Nano Temper Pages: 24

SCAFFOLDBENCH I-CISRL

Brand: MetalTech Pages: 16

Brand: Varan Motors Pages: 70

Brand: Nolangroup Pages: 24

Brand: Eurotops Pages: 8

Brand: KRATOS SAFETY Pages: 36

Brand: HydroHoist Pages: 19

Brand: Advwin Pages: 8

POWER RUN 14.0 HRC

Brand: Energetics Pages: 43

Brand: Monteris Medical Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands