MR VACUTAP VR Installation And Commissioning Instructions Download Page 216 | Manualshive

Page: 216 / 268

background image

10 Transporting transformer to the operating site

Maschinenfabrik Reinhausen GmbH 2015

216

4349315/00 EN

VACUTAP® VR®

Emptying oil compartment via pipe connection S

WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory

control, pressure relief device, pressure-operated relays) before remov-
ing the on-load tap-changer head cover.

► Do not operate any electric devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes and pump equipment

that are approved for flammable liquids.

1.

De-energize all auxiliary circuits (for example the tap-change superviso-
ry control, pressure relief device, pressure monitoring device).

2.

If the stop-cock (slide valve) between the oil conservator and oil com-
partment is open, open the air-vent valve E1 on the on-load tap-changer
head.

3.

Drain off the gas from under the on-load tap-changer cover. Ensure suf-
ficient fresh air (for example in transformer cells and work tents).

4.

Once the gas has been drained off and the oil is flowing out of the air-
vent valve, close this valve and close the stop-cock between the oil con-
servator and oil compartment.

5.

Open air-vent valve again and drain off around 5–10 liters of oil via the
pipe connection S until the area under the on-load tap-changer head
cover is free of oil.

6.

Loosen 24 screws M10/wrench size 17 with safety elements on on-load
tap-changer head cover.

7.

Remove the on-load tap-changer head cover.

8.

Extract oil via pipe connection S.

9.

Open stop-cock between oil conservator and oil compartment.

ð

The oil from the oil conservator flows into the oil compartment.

10. Extract oil via pipe connection S.
11. Place the on-load tap-changer head cover on the on-load tap-changer

head.

12. Use 24 screws M10/wrench 17 and safety elements to screw down on-

load tap-changer head cover (tightening torque 34 Nm).

10.3.1

«
...
214
215
216
217
218
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: ICS Schneider Messtechnik Pages: 124

MicroVersaTrip Plus

Brand: GE Pages: 20

MicroVersaTrip Plus

Brand: GE Pages: 2

Brand: GE Pages: 252

Brand: Balanced Body Pages: 12

Brand: Eagle Pro Pages: 6

Brand: GE Pages: 10

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Dynapro ET 355 Monitor HL

Brand: 3M Pages: 23

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands