MR VACUTAP VR Installation And Commissioning Instructions Download Page 211 | Manualshive

Page: 211 / 268

background image

9 Commissioning of on-load tap-changer by transformer manufacturer

Maschinenfabrik Reinhausen GmbH 2015

211

4349315/00 EN

VACUTAP® VR®

2.

Connect the grounding screw of the motor-drive protective housing to
the transformer tank.

Figure 287: Grounding screw on motor-drive unit

3.

When using a temperature sensor, ground the temperature sensor
housing on the on-load tap-changer using the grounding cable.

Performing tests on motor-drive unit

Please contact Maschinenfabrik Reinhausen if any aspect of the tests is not
clear.

Performing function tests

Perform function checks as described in relevant MR operating instructions
"TAPMOTION® ED".

Dielectric tests on transformer wiring

Note the following points for dielectric tests on the transformer wiring:

The motor-drive unit is put through dielectric tests before delivery.
► Before the dielectric test for the transformer wiring, disconnect drive

from the section to be tested to rule out increased component loading
for those components fitted in the motor-drive unit.

Performing trial tap-change operations

Before energizing the transformer, test tap change operations must be car-
ried out to check the mechanical functions of on-load tap-changer and mo-
tor-drive unit.

9.3

9.3.1

9.3.2

9.4

«
...
209
210
211
212
213
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Parker Pages: 54

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: SALUDA MEDICAL Pages: 61

Brand: Dana Design Pages: 20

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: GE Pages: 18

Brand: Masterclock Pages: 19

Brand: KAM Pages: 5

Brand: MadLab Pages: 7

Brand: ACS Pages: 28

Brand: Cooper Pages: 10

Brand: Korg Pages: 32

COLORado Ridge IP

Brand: Chauvet Pages: 8

ColorSource Fresnel V

Brand: ETC Pages: 16

Brand: Leister Pages: 108

Brand: Dale Tiffany Pages: 2

MEGA STROBE/DMX

Brand: American DJ Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands