MR VACUTAP VR Installation And Commissioning Instructions Download Page 165 | Manualshive

Page: 165 / 268

background image

8 Fitting protective devices and drive components

Maschinenfabrik Reinhausen GmbH 2015

165

4349315/00 EN

VACUTAP® VR®

4.

Close terminal box.

Figure 218: Terminal box cover

The associated contact positions for checking electrical continuity are evi-
dent from the dimensional drawing provided.

Installing protective relay in piping

The following requirements must be satisfied in order to install the protective
relay in the piping:
▪

The pipes from the protective relay to the oil conservator must be routed
with an inclination of at least 2 % to ensure the switching gases can es-
cape freely.

▪

The inner piping diameter must be at least 25 mm.

▪

The magnetic field strength (bushings, busbars etc.) must be < 20 kA/m.

▪

Install protective relay with good support and free from vibrations.

▪

The test buttons must be at the top.

8.2.2

«
...
163
164
165
166
167
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: ABB Pages: 11

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: lancer Pages: 12

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: Nel-Tech Labs Pages: 8

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

Brand: Waterpik Pages: 2

Brand: Pani Pages: 12

Brand: unicraft Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands