MR VACUTAP VR Installation And Commissioning Instructions Download Page 101 | Manualshive

Page: 101 / 268

background image

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

101

4349315/00 EN

VACUTAP® VR®

3.

Temporarily fasten on-load tap-changer to supporting structure. The
supporting flange has through holes for this purpose.

Figure 112: Fastening the on-load tap-changer

Connecting tap winding and on-load tap-changer take-off
lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads which place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer!
► Produce connections with care.
► Do not twist connection contacts.
► Connect connecting leads without warping or deforming.
► If necessary use an expansion loop for connecting leads.
► Fit screening caps provided to screw connections.

The tap winding and on-load tap-changer take-off lead must be connected in
accordance with the connection diagram included with the delivery.

Tap selector connection contacts VRC/VRE

The selector connection contacts are indicated on the selector bars, have
crimped ends and a through-hole for M10 screws to allow the selector take-
off leads to be connected by means of cable shoes.

The screening caps are supplied separately.

In this case a locking washer must be placed below each screening cap. The
M10 connection screws, the nuts, and locking washers are not included in
the scope of delivery.

6.3

6.3.1

«
...
99
100
101
102
103
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Parker Pages: 54

Brand: Baileigh Industrial Pages: 40

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Hach Pages: 66

Brand: Hach Pages: 14

Brand: Hach Pages: 144

QuikChem 8500 2 Series

Brand: Hach Pages: 80

Brand: Hach Pages: 178

Brand: Hach Pages: 32

Brand: hager Pages: 4

Brand: Rainin Instrument Pages: 16

Brand: Qtx Pages: 6

Brand: Dräger Medical Pages: 204

Brand: Jandy Pages: 52

Brand: Emos Pages: 8

Brand: Baileigh Industrial Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands