MR VACUTAP VR Installation And Commissioning Instructions Download Page 223 | Manualshive

Page: 223 / 268

background image

12 Fault elimination

Maschinenfabrik Reinhausen GmbH 2015

223

4349315/00 EN

VACUTAP® VR®

Fault elimination

WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory

control, pressure relief device, pressure-operated relays) before remov-
ing the on-load tap-changer head cover.

► Do not operate any electric devices during the work (for example risk of

sparks caused by impact wrench).

► Only use conductive and grounded hoses, pipes and pump equipment

that are approved for flammable liquids.

NOTICE

Damage to the on-load tap-changer and transformer!

Tripping of the protective relay or other protective devices can indicate dam-
age on the on-load tap-changer and transformer! The transformer must not
be energized without first undertaking checks!
► Check on-load tap-changer and transformer when protective relay or

other protective devices have been tripped.

► Do not use the equipment again until you are sure there is no damage

to the on-load tap-changer or transformer.

The table below is intended to assist with detecting and, where possible,
remedying faults.

For more information, please consult the operating instructions for the RS
protective relay or the relevant protective device.

In the event of faults on the on-load tap-changer and motor-drive unit, which
cannot be easily corrected on site, or if the RS protective relay or additional
protective devices have been tripped, please inform your authorized MR rep-
resentative, the transformer manufacturer or contact us directly at:

Maschinenfabrik Reinhausen GmbH
Technischer Service
Postfach 12 03 60
93025 Regensburg
Germany
Phone: +49 94140 90-0
Fax: +49 9 41 40 90-7001
E-mail: [email protected]
Internet: www.reinhausen.com

Error pattern

Action

Tripping of protective relay (for example RS)

12

«
...
221
222
223
224
225
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Makerfire Pages: 10

Brand: Omnia Pages: 8

Brand: Raven Pages: 27

Brand: Raven Pages: 79

Brand: Raven Pages: 88

Brand: Cadman Pages: 66

Brand: Dairyland Pages: 21

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: GALBIATI Pages: 20

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: ICP DAS USA Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands