MR VACUTAP VR Installation And Commissioning Instructions Download Page 225 | Manualshive

Page: 225 / 268

background image

12 Fault elimination

Maschinenfabrik Reinhausen GmbH 2015

225

4349315/00 EN

VACUTAP® VR®

Error pattern

Action

Deviation from desired value during transformer ratio
test

Contact manufacturer of transformer and, if necessa-
ry, MR and provide measured values.

Deviation from limit value for diverter switch oil val-
ues

Carry out oil change, check oil conservator breather
of on-load tap-changer.

Table 10: Fault elimination

Tripping of the protective relay and re-commissioning the
transformer

WARNING

Danger of death or severe injury!

Danger of death or severe injury if on-load tap-changer and transformer are
insufficiently tested!
► Be sure to check on-load tap-changer and transformer after the protec-

tive relay has been tripped. The diverter switch insert or selector switch
insert must be removed in order to do this.

► Only use the equipment again when you are sure there is no damage to

the on-load tap-changer or transformer.

When the circuit breakers have been tripped by the protective relay, proceed
as follows:
1.

Establish time of tripping.

2.

Determine operating position of on-load tap-changer.

3.

As a precaution, block the motor-drive unit by tripping the motor protec-
tive switch to prevent the on-load tap-changer being actuated by remote
control.

4.

Check on-load tap-changer head cover. If oil is leaking, shut the oil con-
servator stop valve immediately.

5.

Check whether the flap valve of the protective relay is in the OFF or IN
SERVICE position.

Flap valve in IN SERVICE position

If the flap valve is in the IN SERVICE position, there may be a fault in the
tripping circuit. Check the tripping circuit. If the reason for the protective relay
tripping cannot be found, the diverter switch insert or selector switch insert
must be removed in accordance with the on-load tap-changer's operating in-
structions and checked [

Flap valve in OFF position

Note that protective relay RS 2004 features an automatic reset mechanism
which means that the flap valve does not remain in the OFF position after
tripping. If the protective relay RS 2004 has not tripped due to an error in
the tripping circuit, proceed as described below for RS 2004 too.

12.1

12.1.1

12.1.2

«
...
223
224
225
226
227
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Haigh Pages: 60

Crouse-hinds series

Brand: Eaton Pages: 32

COOPER POWER SERIES

Brand: Eaton Pages: 8

Brand: Olympus Pages: 56

Brand: Rath Pages: 5

C-HB-A-LB2-SCCT Series

Brand: C-LITE Pages: 9

X-431 Torque HD

Brand: Launch Pages: 3

GPSMAP 9 3 Series

Brand: Garmin Pages: 222

Brand: Buki Pages: 16

Brand: Sentinel Pages: 4

Brand: PASCO Pages: 36

Brand: Otto Bock Pages: 52

Brand: Torin BIG RED Pages: 43

Turbo Jet 10 i-CON

Brand: Stocks AG Pages: 30

Randell DROP-IN 9550-290

Brand: Unified Brands Pages: 16

Brand: E-LINK Pages: 4

Brand: Magicfx Pages: 32

Brand: chinavasion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands