MR VACUTAP VR Installation And Commissioning Instructions Download Page 50

Page: 50 / 268

5 Assembly: Standard design

Maschinenfabrik Reinhausen GmbH 2015

4349315/00 EN

VACUTAP® VR®

Securing tap selector on oil compartment of the on-load tap-
changer VRG

WARNING!

Place the selector on a level surface and secure it

against tipping

CAUTION!

. An unstably positioned selector may tip,

resulting in serious injuries and damage.

Remove plastic bag with fastening materials from the selector and lay
out.

Figure 31: Plastic bag with fastening materials

Remove the blocking strip from the selector coupling. Once the blocking
strip is removed, the selector coupling must no longer be turned.

Figure 32: Blocking strip

Place the selector on the lifting device. The weight of the selector is a
maximum of 465 kg.

5.2.4

Summary of Contents for VACUTAP VR













































































































































































































































































Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands

MR VACUTAP VR, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands