MR VACUTAP VR Installation And Commissioning Instructions Download Page 16 | Manualshive

Page: 16 / 268

background image

2 Safety

Maschinenfabrik Reinhausen GmbH 2015

16

4349315/00 EN

VACUTAP® VR®

DANGER

Danger of death or severe injury and damage to property and
the environment!

Danger of death or severe injury and damage to property and the environ-
ment due to electrical voltage, falling and/or tipping parts as well as danger-
ous cramped conditions resulting from moving parts!
► Adherence to the following prerequisites and conditions is mandatory.
► Adhere to warning notices.

Since the on-load tap-changer was dimensioned as per IEC 60214-1, it can
switch currents of up to twice the value of the rated through current.

On-load tap-change operations are not to be performed during operating
conditions with higher currents.

Examples of such operating conditions are:
▪

Inrush current impulses when transformers are switched on

▪

Short circuit

The rated step voltage may be briefly exceeded by up to 10 % as long as the
rated through current is not exceeded. Such an operating condition can oc-
cur due to overexcitation of the transformer after load shedding, for example.

The on-load tap-changer can be operated in the temperature range of the
surrounding transformer oil of between -25 ° and +105 °C and with overload
up to +115 °C in accordance with IEC 60214-1.

Inappropriate use

Use is considered to be inappropriate if the product is used other than as de-
scribed in the Appropriate use [

15] section. Please also note the following:

▪

Risk of explosion and fire from highly flammable or explosive gases, va-
pors, or dusts. Do not operate product in areas at risk of explosion.

▪

Unauthorized or inappropriate changes to the product may lead to per-
sonal injury, material damage, and operational faults. Only modify prod-
uct following discussion with Maschinenfabrik Reinhausen GmbH.

Personnel qualification

The product is designed solely for use in electrical energy systems and facili-
ties operated by appropriately trained staff. This staff comprises people who
are familiar with the installation, assembly, commissioning and operation of
such products.

2.3

2.4

«
...
14
15
16
17
18
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: Faderfox Pages: 8

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: York Fitness Pages: 20

Brand: Maeda Pages: 276

Brand: Madsen Pages: 206

Brand: Qlight Pages: 4

Brand: Yamaha Pages: 126

DM 2000 Version 2

Brand: Yamaha Pages: 8

PowerGen 5650 Series

Brand: Qnergy Pages: 10

Brand: Wang Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands