MR VACUTAP VR Installation And Commissioning Instructions Download Page 181 | Manualshive

Page: 181 / 268

background image

8 Fitting protective devices and drive components

Maschinenfabrik Reinhausen GmbH 2015

181

4349315/00 EN

VACUTAP® VR®

NOTICE

Damage to the on-load tap-changer!

Damage to the on-load tap-changer by actuating the on-load tap-changer
without oil!
► Before actuating the on-load tap-changer for the first time, the tap se-

lector must be completely immersed in transformer oil and the oil com-
partment completely filled with oil.

► The on-load tap-changer can be operated in the temperature range of

the surrounding transformer oil of between -25 ° and +105 °C and with
overload up to +115 °C in accordance with IEC 60214-1.

Observe the following during mounting:

NOTICE

Damage to drive and on-load tap-changer or off-circuit tap-
changer!

Trouble-free operation of the motor-drive and the on-load tap-changer or
off-circuit tap-changer cannot be guaranteed.
► The shaft ends to be connected must be exactly aligned.

Minor axial displacement can be tolerated as long as it does not exceed
35 mm per 1000 mm square tube length (that corresponds to 2°).

Square tubes, coupling brackets, coupling bolts, screws, and locking wash-
ers are corrosion-resistant. We therefore recommend not applying the same
external coating to these parts as to the transformer tank.

The square tubes and the vertical protective cover are supplied in over-
lengths (graded standard lengths). These parts must be cut to the required
size before mounting on the transformer. In rare cases the inner tube of the
telescopic protective tube has to be cut.

Standard lengths

Motor-drive unit

Manual drive

400

•

•

600

•

•

900

•

•

1300

•

•

1700

•

•

2000

•

•

2500

Not permitted

•

1)

Table 9: Graded standard lengths of square tubes

The maximum total drive shaft length of the drive - last pole = 15 m.

1)

I>2000 only possible for vertical installation without shaft protection! Tele-

scopic protective tubes for manual drives with vertical dimensions V1> 2462
should be delivered vertically, similar to the motor-drive unit with intermedi-
ate bearing.

«
...
179
180
181
182
183
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Qingdao H.Y Pages: 6

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Landoll Pages: 83

Brand: FEAS Pages: 72

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: R.M. Young Pages: 10

Brand: Taylor Pages: 60

Brand: TANDBERG Pages: 23

Brand: Raytec Pages: 60

Brand: UniPix Pages: 24

Brand: ZOLL Pages: 37

Brand: Wacker Neuson Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands