MR VACUTAP VR Installation And Commissioning Instructions Download Page 7

Page: 7 / 268

Table of contents

Maschinenfabrik Reinhausen GmbH 2015

4349315/00 EN

VACUTAP® VR®

8.2.2

Installing protective relay in piping.................................................................................................................... 165

8.2.3

Installing electrics for protective relay............................................................................................................... 168

8.3

Installing and connecting the pressure-operated relay.................................................................... 174

8.3.1

Checking the function of the pressure-operated relay....................................................................................... 174

8.3.2

Installing the pressure-operated relay............................................................................................................... 176

8.3.3

Making the electrical connections for the pressure-operated relay................................................................... 177

8.4

Fitting motor-drive unit on transformer............................................................................................ 178

8.5

Fitting bevel gear............................................................................................................................. 180

8.6

Fitting drive shaft............................................................................................................................. 180

8.6.1

Fitting vertical drive shaft................................................................................................................................... 182

8.6.2

Fitting horizontal drive shaft.............................................................................................................................. 189

8.6.3

Fitting drive shaft with cardan joints.................................................................................................................. 194

8.6.4

Fitting drive shaft with insulator......................................................................................................................... 207

8.7

Centering on-load tap-changer and motor-drive unit....................................................................... 208

8.8

Installing electrics for motor-drive unit............................................................................................. 208

Commissioning of on-load tap-changer by transformer manufacturer..................... 209

9.1

Bleeding on-load tap-changer head and suction pipe..................................................................... 209

9.1.1

Bleeding on-load tap-changer head.................................................................................................................. 209

9.1.2

Bleeding suction pipe on pipe connection S...................................................................................................... 210

9.2

Grounding the on-load tap-changer................................................................................................. 210

9.3

Performing tests on motor-drive unit............................................................................................... 211

9.3.1

Performing function tests................................................................................................................................... 211

9.3.2

Dielectric tests on transformer wiring................................................................................................................ 211

9.4

Performing trial tap-change operations........................................................................................... 211

9.5

High-voltage tests on the transformer............................................................................................. 212

Transporting transformer to the operating site........................................................... 214

10.1

Transport with removed drive.......................................................................................................... 214

10.2

Transport with oil fill and without oil conservator............................................................................. 214

10.3

Transport without oil fill.................................................................................................................... 215

10.3.1

Emptying oil compartment via pipe connection S.............................................................................................. 216

Commissioning transformer at installation site........................................................... 217

11.1

Checking motor-drive unit................................................................................................................ 217

11.2

Checking protective relay................................................................................................................ 218

11.2.1

Checking protective relay (RS 2001, 2001/V, 2001/H, 2001/E, 2001/5, 2001/R, 2003).................................... 218

Summary of Contents for VACUTAP VR













































































































































































































































































Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands

MR VACUTAP VR, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands