MR VACUTAP VR Installation And Commissioning Instructions Download Page 212 | Manualshive

Page: 212 / 268

background image

9 Commissioning of on-load tap-changer by transformer manufacturer

Maschinenfabrik Reinhausen GmbH 2015

212

4349315/00 EN

VACUTAP® VR®

NOTICE

Damage to the on-load tap-changer!

Damage to the on-load tap-changer by actuating the on-load tap-changer
without oil!
► Before actuating the on-load tap-changer for the first time, the tap se-

lector must be completely immersed in transformer oil and the oil com-
partment completely filled with oil.

► The on-load tap-changer can be operated in the temperature range of

the surrounding transformer oil of between -25 ° and +105 °C and with
overload up to +115 °C in accordance with IEC 60214-1.

1.

Undertake tap change operation tests across entire range of settings.

2.

NOTICE!

Make sure that in each operating position the tap position in-

dicators of motor-drive unit and on-load tap-changer (inspection window
in the on-load tap-changer head) read the same position. An incorrectly
coupled motor-drive unit will damage the on-load tap-changer.

High-voltage tests on the transformer

WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover, in the pipework system, in the oil conservator, at
the dehydrating breather opening, and from flying parts and hot oil splash-
ing!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

► Ensure that the oil compartment of the on-load tap-changer is com-

pletely filled with oil.

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

► Ensure that all the on-load tap-changer's safety equipment is ready for

use.

► Use suitable personal protective equipment/clothing.
► Keep away from the danger area during the transformer test.
► Observe applicable fire protection regulations.
► Make sure that only trained technicians perform work on the transform-

er.

It is essential that you ensure only trained, instructed expert personnel who
are familiar with and comply with the pertinent safety and technical regula-
tions, who are aware of the potential risks, and who consistently use the oc-
cupational safety equipment provided to prevent injury and property damage
are assigned to perform such a transformer test.

9.5

«
...
210
211
212
213
214
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Major Pages: 52

Brand: SAMCHULLY Pages: 48

Brand: HAGER WERKEN Pages: 2

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Brand: M-Audio Pages: 3

Brand: YMC Pages: 49

Brand: Octane Fitness Pages: 8

Brand: Octane Fitness Pages: 10

Brand: OCENCO Pages: 48

Brand: Ocean Optics Pages: 6

Brand: Abus Pages: 12

Brand: Garden Treasures Pages: 2

Brand: XpressFill Pages: 11

Brand: Goobay Pages: 6

Brand: Daihan Scientific Pages: 27

WEEDDEVIL ST-97

Brand: R+M Suttner Pages: 16

Brand: Viking Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands