MR VACUTAP VR Installation And Commissioning Instructions Download Page 109

Page: 109 / 268

6 Assembly: Bell-type tank design

Maschinenfabrik Reinhausen GmbH 2015

109

4349315/00 EN

VACUTAP® VR®

Parallel bridges for VRG I 1601

Bridges for connecting the connection contacts of the fine tap selector and
change-over selector in parallel in accordance with drawing 786920 [

►

238]

will be supplied.

Connecting on-load tap-changer take-off lead

There are through-holes 13 mm in diameter at three points on the oil com-
partment's connecting ring.
1.

Connect the on-load tap-changer take-off lead to the connecting ring of
the oil compartment.

Secure screw connection.

Figure 125: On-load tap-changer take-off lead

Carrying out the transformer ratio test

We recommend carrying out a transformer ratio test before the transformer
is dried. The following types of transformer ratio test are possible:
▪

Transformer ratio test with TAPMOTION® TD test drive

▪

Manual transformer ratio test

6.3.10

6.3.11

6.4

Summary of Contents for VACUTAP VR













































































































































































































































































Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands

MR VACUTAP VR, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR

Reviews:

Related manuals for VACUTAP VR

Brands by name

Popular brands