Mitsubishi Electric AnyWire ASLINK User Manual Download Page 18 | Manualshive

Page: 18 / 200

background image

16

2 SPECIFICATIONS
2.2 Performance Specifications

2.2

Performance Specifications

The following table lists the performance specifications.

*1 For the number of points used in the NZ2AW1GNAL, refer to the following.

Page 127 Remote I/O Signals

Page 141 Remote Register

*2 For the network topology, follow the specifications of the master station used.
*3 For wiring of 50m or more with 4 wires (DP, DN, 24V, 0V), insert the noise filter for power supply cables between the power supply and

cables. For details, refer to the manual for the AnyWireFILTER (ANF-01) manufactured by Anywire Corporation.

*4 For the relationship between the total length, the wire diameter of transmission cables (DP, DN), and the transmission cable supply

current, refer to the following. On some slave modules with cables, the wire diameter of module-integrated transmission cables (DP, DN)
may be 0.75



or less. However, they can be used without any problem, provided that the diameter of the transmission cables (DP,

DN) meets the requirement below.

*5 When the 24VDC power is supplied from the NZ2AW1GNAL to slave modules, ensure that the total amount of the transmission cable

supply current and the current supplied to slave modules does not exceed 2A.

Classification

Item

Specifications

CC-Link IE TSN

Station type

Remote station

Authentication Class

Authentication Class B

Maximum number of link points

Remote input (RX)

544 points

Remote output (RY)

544 points

Remote register (RWw)

544 words

Remote register (RWr)

544 words

Network topology

Line topology, star topology, coexistence of line and star topologies, ring topology

AnyWireASLINK

Transmission clock

27.0kHz

Maximum transmission distance
(total length)

200m

Transmission method

DC power supply superimposed total frame/cyclic method

Connection type

Bus topology (multidrop system, T-branch system, tree branch system)

Transmission protocol

Dedicated protocol (AnyWireASLINK)

Error control

Checksum, double-verification system

Number of bit data points

1024 points maximum (input: 512 points, output: 512 points)

Number of word data points

1024 points maximum (input: 512 points, output: 512 points)

Number of connected slave
modules

256 maximum (varies depending on the current consumption of each slave module)

RAS function

Disconnected transmission cable location detection function, transmission cable short detection
function, module power supply drop detection function

AnyWireASLINK transmission
cable
24VDC power cable

• UL-listed general-purpose 2-wire cable (VCTF, VCT 1.25



, 0.75



, temperature rating 70



or higher)

• UL-listed general-purpose wire (1.25



, 0.75



, temperature rating 70



or higher)

• Dedicated flat cable (1.25



, 0.75



, temperature rating 90



)

Transmission cable supply
current

2A maximum

Common

Power supply

Voltage: 21.6 to 27.6VDC (24VDC -10 to +15%), ripple 0.5Vp-p or lower
Recommended voltage: 26.4VDC (24VDC + 10%)
Module current consumption: 0.2A

External dimensions

102mm(H)



43mm(W)



102.8mm(D)

Weight

0.2kg

Wire diameter of transmission
cables (DP, DN)

Transmission cable supply current

Total length of 50m or less

Total length of 50m to 100m

Total length of 100m to 200m

1.25



2A maximum

1A maximum

0.5A maximum

0.75



1.2A maximum

0.6A maximum

0.3A maximum

«
...
16
17
18
19
20
...
»

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Related manuals for AnyWire ASLINK

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: jablotron Pages: 22

Brand: jablotron Pages: 2

Brand: Omega Pages: 56

Brand: Omega Pages: 2

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: NEC Pages: 30

CPX-AP-A-16DI-D-M12-5P

Brand: Festo Pages: 16

Brand: tell Pages: 11

Easywave ST01 Series

Brand: Eldat Pages: 2

Brand: FADAL Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands