manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 137

APPX

Appendix 1  Remote I/O Signals

135

A

One slave module easy replacement in progress flag

■

Device No.

■

Description

This flag turns on during the slave module replacement using the easy replacement function for one slave module.

One slave module easy replacement completion flag

■

Device No.

■

Description

This flag turns on when the slave module replacement using the easy replacement function for one slave module is 
completed. It turns on for five seconds and then automatically turns off.

Automatic address detection operation mode

■

Device No.

■

Description

The status of operation mode of automatic address detection can be checked.
 • In standard mode: Off
 • In high-speed mode: On

Name

Device No.

One slave module easy replacement in progress flag

RX16

Name

Device No.

One slave module easy replacement completion flag

RX17

Name

Device No.

Automatic address detection operation mode

RX18

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands