manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 111

10  TROUBLESHOOTING

10.1  Checking with LEDs

109

10

10

TROUBLESHOOTING

This chapter describes the details of errors that may occur when using the NZ2AW1GNAL and troubleshooting.

10.1

Checking with LEDs

This section describes troubleshooting using the LEDs.

Determining the module error status

The error status can be determined as follows by the status of the RUN LED and ERR. LED.

*1 If multiple errors occur, the error status is displayed in the order of major error > moderate error > minor error.
*2 If a module is in failure, the LED may not turn on.

If the PW LED does not turn on

If the PW LED does not turn on, check the following items.

If the RUN LED does not turn on

If the RUN LED does not turn on, check the following items.

When the RUN LED flashes

When the RUN LED flashes, check the following items.

RUN LED

ERR. LED

Error type

*1

Description

Off

On

*2

Major error

This error stops operation of the module and requires consultation with your local Mitsubishi 
representative.

On

On

Moderate error

This error stops operation of the module but can be dealt with by the customer.

On

Flashing

Minor error

This error does not stop the module from operating.

Check item

Action

Are any LEDs other than the PW LED on?

If any LEDs other than the PW LED are on, the possible cause is a hardware error. Please 
consult your local Mitsubishi representative.

Is the module power supply (24VDC) wired?

Wire the module power supply (24VDC).

Is the module power supply (24VDC) turned on?

Turn on the module power supply (24VDC).

Is the voltage of the module power supply (24VDC) within the 
specified range?

Keep the voltage value within the performance specifications.

Check item

Action

Has a hardware error occurred?

Power off and on the module power supply (24VDC).
If the RUN LED does not turn on, the module may be in failure.
Please consult your local Mitsubishi representative.

Check item

Action

Is the unit test running?

After the unit test is completed, turn off the module power supply. After turning off the module 
power supply (24VDC), turn off MODE switch 1 and turn the module power supply from off to 
on.

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands