manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 134

132

APPX
Appendix 1  Remote I/O Signals

Number of transmission points setting switch enable/disable status flag

■

Device No.

■

Description

The status of number of transmission points of AnyWireASLINK setting switch can be checked.
 • When enabled: ON
 • When disabled: OFF

Even if the switch is changed after the module is started, because the module operation does not change, the 
value of Number of transmission points setting switch enable/disable status flag (RX9) does not change and 
the state at the time of module start-up is maintained.
If the number of points is set from the engineering tool when the number of transmission points of 
AnyWireASLINK setting is enabled, an error will occur.

Module parameter reflection completion flag

■

Device No.

■

Description

When setting the module parameters from the program, Module parameter reflection request flag (RYC) turns on and this 
signal turns on when the parameter data writing to the non-volatile memory is completed.
This signal automatically turns off when Module parameter reflection request flag (RYC) turns off.

AnyWireASLINK version compatibility inspection executing flag

■

Device No.

■

Description

This signal turns on when the AnyWireASLINK version compatibility inspection is started.

■

Turning off AnyWireASLINK version compatibility inspection executing flag

AnyWireASLINK version compatibility inspection executing flag (RXD) turns off when the following conditions are met.
 • The AnyWireASLINK version compatibility inspection has completed.
 • AnyWireASLINK version compatibility inspection command (RYD) is turned on and off.

Name

Device No.

Number of transmission points setting switch enable/disable status flag

RX9

Name

Device No.

Module parameter reflection completion flag

RXC

Name

Device No.

AnyWireASLINK version compatibility inspection executing flag

RXD

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands