manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 36

34

5  INSTALLATION AND WIRING
5.5  Wiring to a Transmission Cable Terminal Block of the AnyWireASLINK

Precautions

 • In the AnyWireASLINK system, signals and power are supplied to a slave module with two transmission cables: DP and 

DN. Therefore, use a stranded wire of 0.75

 or larger as the main line.

 • Wires such as general-purpose wires, cabtyre cables, and flat cables can be used.
 • Do not run multiple transmission cables (DP, DN) using a multicore cable. Run multiple transmission cables (DP, DN) are 

affected by noise, causing a malfunction.

 • The voltage should not fall below the lower limit of the allowable voltage range due to a voltage drop caused by the cable. If 

the voltage falls below the lower limit, malfunctions may occur.

 • Do not connect soldered cables directly to the terminals.
 • Use bar solderless terminals for the wiring to the terminal block. If inserted as is, a stripped cable cannot be clamped 

properly in a wire insertion opening.

 • Use a crimping tool to connect a cable to a bar solderless terminal.
 • Before inserting a bar solderless terminal, check the shapes of the wire insertion opening and bar solderless terminal. 

Then, insert the terminal in the correct orientation. Inserting a bar solderless terminal wider than the wire insertion opening 
may damage the terminal block. (

 Page 32 Solderless terminal)

 • Signal names are not printed on the transmission cable terminal block. To avoid incorrect wiring, wire cables to the terminal 

block attached to the NZ2AW1GNAL.

 • Do not insert multiple bar solderless terminals into one wire insertion opening. Doing so may cause damage on the terminal 

block or cable, or malfunction.

DP
DN
DP
DN

DP
DN
DP
DN

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands