Mitsubishi Electric AnyWire ASLINK User Manual Download Page 7 | Manualshive

Page: 7 / 200

background image

5

[Startup and Maintenance Precautions]

[Startup and Maintenance Precautions]

[Disposal Precautions]

WARNING

●

Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.

●

Shut off the external power supply (all phases) used in the system before cleaning the module,
retightening the terminal block screws or connector screws, or operating the IP address/station
number setting switches. Failure to do so may cause the module to fail or malfunction.

CAUTION

●

Do not disassemble or modify the module. Doing so may cause failure, malfunction, injury, or a fire.

●

Do not drop or apply strong shock to the module. Doing so may damage the module.

●

Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone
System) more than 25cm away from wiring as well as away in all directions from the programmable
controller. Failure to do so may cause malfunction.

●

Shut off the external power supply (all phases) used in the system before mounting or removing a
module. Failure to do so may cause the module to fail or malfunction.

●

After the first use of the product, do not connect/remove the terminal block more than 50 times (IEC
61131-2/JIS B 3502 compliant). Exceeding the limit may cause malfunction.

●

After the first use of the product, do not connect/remove the connector more than 50 times (IEC
61131-2/JIS B 3502 compliant). Exceeding the limit may cause malfunction.

●

Before handling the module or connection cables, touch a conducting object such as a grounded
metal to discharge the static electricity from the human body. Failure to do so may cause the module
to fail or malfunction.

●

Startup and maintenance of a control panel must be performed by qualified maintenance personnel
with knowledge of protection against electric shock. Lock the control panel so that only qualified
maintenance personnel can operate it.

●

Use a clean and dry cloth to wipe off dirt on the module.

CAUTION

●

When disposing of this product, treat it as industrial waste.

«
...
5
6
7
8
9
...
»

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Related manuals for AnyWire ASLINK

Brand: Eaton Pages: 16

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: D+H Pages: 14

Brand: Datavideo Pages: 8

Brand: Van Air Pages: 4

Brand: Maestra Pages: 22

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Brand: SYCLOPE electronic Pages: 40

Brand: Timotion Pages: 10

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: Aurora Pages: 2

Snappi Pushchair

Brand: Tendercare Pages: 76

Brand: Apex Toys Pages: 7

Brand: Baier Pages: 20

Brand: Forcepoint Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands