Mitsubishi Electric AnyWire ASLINK User Manual Download Page 32

Page: 32 / 200

5 INSTALLATION AND WIRING
5.3 Installation

5.3

Installation

Mounting a module on a DIN rail

Removing a module from a DIN rail

5.4

CC-Link IE TSN Connector Wiring

For the connection of CC-Link IE TSN connector, refer to the following.



User's manual for the master station used

Hook the upper fixing tab on the bottom of the
module to the DIN rail.

Push and engage the NZ2AW1GNAL on the DIN
rail.

Insert a flathead screwdriver into the hook and pull
the hook to remove from the DIN rail.

Lift the module on the hook side and remove it
using the fixing tab as the supporting point.

Summary of Contents for AnyWire ASLINK









































































































































































































Search results

Summary of Contents for AnyWire ASLINK

Reviews:

Related manuals for AnyWire ASLINK

Brands by name

Popular brands

Mitsubishi Electric AnyWire ASLINK, User Manual

Search results

Summary of Contents for AnyWire ASLINK

Reviews:

Related manuals for AnyWire ASLINK

Brands by name

Popular brands