Mitsubishi Electric AnyWire ASLINK User Manual Download Page 40

Page: 40 / 200

5 INSTALLATION AND WIRING
5.8 Checking System Before Power-on

5.8

Checking System Before Power-on

This section describes the items to be checked before power-on.

Check that the NZ2AW1GNAL is mounted correctly. (



Page 28 Installation Environment and Installation Position)

Check that the station-to-station distance of CC-Link IE TSN is within the specified range. (



Page 16 Performance

Specifications)

Check that the maximum transmission distance (total length) of the AnyWireASLINK system is within the specified
range. (



Page 16 Performance Specifications)

Check that the power supplied to the NZ2AW1GNAL is within the specified range. (



Page 37 Supplying Power to the

NZ2AW1GNAL)

Check that the NZ2AW1GNAL, slave module, terminating unit, and 24VDC external power supply are properly
connected and wired.

Summary of Contents for AnyWire ASLINK









































































































































































































Search results

Summary of Contents for AnyWire ASLINK

Reviews:

Related manuals for AnyWire ASLINK

Brands by name

Popular brands

Mitsubishi Electric AnyWire ASLINK, User Manual

Search results

Summary of Contents for AnyWire ASLINK

Reviews:

Related manuals for AnyWire ASLINK

Brands by name

Popular brands