Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 68

Page: 68 / 147

CONDITIONS AFFECTING OPERATION

eng

Ventilation

Ventilation occurs when surface air or exhaust gases surround

the propeller, causing propeller speed‑up (slippage) and a

decrease in boat speed. Excessive ventilation is annoying and

usually caused by:

• A drive unit trimmed out too far.
• A damaged propeller or gear housing, allowing exhaust

gases to escape between propeller and gear housing.

• A drive unit installed too high on the transom.

Propeller Selection

IMPORTANT: Choosing the correct propeller allows the engine

to run at its specified maximum wide‑open‑throttle RPM. Use an

accurate service tachometer to verify engine operating RPM.
It is the boat manufacturer and/or the selling dealer's

responsibility to equip the power package with the correct

propeller(s). Specified engine wide‑open‑throttle (WOT) and

operating RPM range are listed in

Specifications.

IMPORTANT: All Mercury Racing engines have an RPM

rev‑limiter that is set to an upper (or limited) RPM. This limit is

slightly above the normal operating range of the engine and is

designed to help prevent damage from excessive engine RPM.

Once the RPM drops into the recommended operating RPM

range, normal engine operation resumes.
Select a propeller that allows the engine to operate in the upper

half of the recommended full throttle RPM range with the boat

normally loaded (refer to

Specifications

If full throttle operation is below the recommended range, change

the propeller to prevent loss of performance and possible engine

damage. On the other hand, operating an engine above the

recommended operating RPM range causes higher than normal

wear or damage. "Propeller lines normally are designed so that

the next size pitch will change engine RPM by 300 to 500. For

every 1" of pitch change, the effect will be approximately 200

RPM."

RPM loss may require changing to a lower pitch propeller
due to the following conditions:

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands