Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 119

Page: 119 / 147

MAINTENANCE

eng

109

NOTE: This test should be made where boat is moored, using a

Reference Electrode and test meter. Contact your authorized

Mercury MerCruiser dealer to arrange for this test.

a -

MerCathode

b -

Electrode assembly

SACRIFICIAL ANODES

Sacrificial anodes

‑

help protect the power package against

galvanic corrosion by sacrificing its metal to be slowly eroded

instead of the metal components on the power package. These

anodes are installed at different location on your power package.

Ventilation plate anode

‑

serves as a sacrificial anode.

Unscrew both attaching screws and remove. Install a new

anodic plate and tighten securely.

a -

Anodic plate

b -

Attaching screw

9322

7009

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands