Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 102

Page: 102 / 147

MAINTENANCE

eng

1. Place a wood block between the propeller blade and the

anti‑ventilation plate to prevent rotation.

2. Remove the screw and washers securing the propeller shaft

anode.

3. Remove the propeller shaft anode.

a -

Propeller

b -

Propeller shaft nut

c -

Propeller shaft anode

d -

Propeller shaft anode screw

e -

Flat washer

f -

Star washer

4. Turn the aft propeller shaft nut 37 mm (1‑7/16 in.)

counter‑clockwise to remove.

5. Slide the propeller and thrust hub off the propeller shaft.
6. Turn the front propeller shaft nut 70 mm (2‑3/4 in.)

counter‑clockwise to remove.

7. Slide the propeller and thrust hub off the propeller shaft.

5303

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands