Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 134

Page: 134 / 147

COLD WEATHER OR EXTENDED STORAGE

124

eng

PRIMING THE FUEL SYSTEM PRIOR TO STARTING

WARNING

Fuel is flammable and explosive. Ensure that the key switch is

off and the lanyard is positioned so that the engine cannot

start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated

and avoid prolonged exposure to vapors. Always check for

leaks before attempting to start the engine, and wipe up any

spilled fuel immediately.

1. Remove the plug from the water separating fuel filter as

shown following and install a barbed fitting into the water

separating fuel filter.

a -

Water seperating fuel filter plug

b -

Barbed fitting

2. Attach an outboard type portable fuel tank with primer bulb

to the barbed fitting with a hose clamp.

3. Squeeze the primer bulb until the bulb becomes firm.

NOTE: Do not turn the key switch to the "START" position

during the following priming procedure.

6166

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands