Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 115

Page: 115 / 147

MAINTENANCE

eng

105

INSPECTING BELT
NOTE: Minor, transverse cracks (across the belt width) may be

acceptable. Longitudinal cracks (in the direction of belt length)

that join transverse cracks are not acceptable.

The belt will have to be replaced for the following conditions:

• Excessive wear
• Cracks or fraying
• Glazed surfaces

a -

Fraying

b -

Transverse cracks

c -

Longitudinal cracks

Changing Fuel Filters

WATER SEPARATING FUEL FILTER

WARNING

Fuel is flammable and explosive. Ensure that the key switch is

off and the lanyard is positioned so that the engine cannot

start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated

and avoid prolonged exposure to vapors. Always check for

leaks before attempting to start the engine, and wipe up any

spilled fuel immediately.

6164

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands