Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 25

Page: 25 / 147

GENERAL INFORMATION

eng

Do not overpower or overload your boat. Most boats will carry a

required capacity plate indicating the maximum acceptable

power and load as determined by the manufacturer following

certain federal guidelines. If in doubt, contact your dealer or the

boat manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

26777

High‑Speed and High‑Performance Boat Operation

If your power package is to be used on a high‑speed or

high‑performance boat with which you are unfamiliar, we

recommend that you never operate it at its high‑speed capability

without first requesting an initial orientation and familiarization

demonstration ride with your dealer or an operator experienced

with your boat/power package combination. For additional

information, obtain a copy of our High‑Performance Boat

Operation booklet from your dealer, distributor, or Mercury

Marine.

Paddle Wheel and Water Temperature Sensors

Paddle wheels cannot be utilized on vessels that are capable of

speeds in excess of 50 mph. Water temperature sensors cannot

be connected to Race sterndrive engines that are equipped with

a propulsion control module (PCM). The water temperatue

sensor connection is utilized by the PCM for monitoring engine

oil temperature.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands