Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 113

Page: 113 / 147

MAINTENANCE

eng

103

• Install new PCV valve into hose, and install into intake

manifold.

• Ensure that the valve is tightly seated in manifold.

Use only Mercury MerCruiser replacement parts.

Serpentine Drive Belt

DRIVE BELT ROUTING AND TENSION

WARNING

Inspecting the belts with the engine running may cause serious

injury or death. Turn off the engine and remove the ignition key

before adjusting tension or inspecting belts.

IMPORTANT: Drive belt must be routed as shown or damage

may result.

1. Loosen the 5/8 in locking nut on adjustment stud. Leave the

wrench on the adjustment nut.

2. Install the belt tension gauge onto the belt.
3. Use a 5/16 in socket and tighten adjusting stud until the belt

tension conforms to the correct setting on the gauge.

4. Hold the adjustment stud and tighten the 5/8 in locking nut.
5. Remove the belt tension gauge from the belt.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands