Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 131

Page: 131 / 147

COLD WEATHER OR EXTENDED STORAGE

eng

121

4. After draining seawater cooling system, install drain plugs

(Perfect Seal is not required on wing nut type plugs),

reconnect hoses and tighten all hose clamps securely.

5. Make sure the following passages are open and

unobstructed:

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

6. For additional assurance against freezing and rust in the

engine seawater cooling system when storing for winter or

long periods of non use, perform the following steps:

IMPORTANT: A nontoxic and environmentally safe ethylene

glycol antifreeze containing a rust inhibitor must be used when

preparing the seawater section of the cooling system for cold

weather or extended storage. Be certain to follow the

manufacturer's recommendations.

NOTE: If the boat is in the water during the following procedure,

the seawater shut off valve must be closed and the hose

removed from the engine side of the valve to avoid water

entering the boat.

8042

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands