Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 1

Page: 1 / 147

eng

Thank You

for your purchase of one of the finest marine power

packages available. It incorporates numerous design

features to ensure operating ease and durability.
With proper care and maintenance, you will thoroughly enjoy

using this product for many boating seasons. To ensure

maximum performance and carefree use, we ask that you

thoroughly read this manual.
The Operation, Maintenance & Warranty Manual contains

specific instructions for using and maintaining your product.

We suggest that this manual remain with the product for

ready reference whenever you are on the water.
Again, thank you for purchasing one of our Mercury Marine

products. We sincerely hope your boating will be pleasant!

Mercury Racing,

N7480 County Road "UU"

Fond du Lac, WI 54935-9585

7406

Warranty Message

WARNING

The operator (driver) is responsible for the correct and

safe operation of the boat, the equipment aboard and the

safety of all occupants aboard. We strongly recommend

that the operator read this Operation, Maintenance and

Warranty Manual and thoroughly understand the

operational instructions for the power package and all

related accessories before the boat is used.

HP525 EFI Bravo Sterndrive Models

90-8M0079397 513

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands